Industrial Plug & Socket Price in Pakistan 2026 — IP44/IP66/IP67 Buyer Guide
An industrial plug and socket is the rugged, weather-sealed power connector you fit on every Pakistani factory floor, every solar shop, every petrol station's outdoor power source, and every commercial building's pantry. Unlike domestic 3-pin sockets that can handle 13A, industrial sockets carry 16A to 125A at 220V or 380V, are IP44 to IP67 rated, and can be replaced 10,000 times before contact wear matters.
This guide covers industrial plug and socket prices in Pakistan for 2026, the IP44 vs IP66 sealing distinction, 3-pin vs 4-pin vs 5-pin variants, and the IEC 60309 standard your factory inspector will check.
1. The IEC 60309 standard
Every legitimate industrial plug + socket sold in Pakistan should meet IEC 60309-1/2. Key markings:
- Pin count: 2P + E (single-phase + earth), 3P + E (3-phase no neutral + earth), 3P + N + E (3-phase + neutral + earth = 5-pin)
- Voltage colour code: blue = 230V single-phase, red = 400V 3-phase, yellow = 110V (rare in PK), green = 24V SELV
- IP rating: IP44 (dust-resistant + splash-proof) for indoor, IP66 (dust-tight + powerful water jet) for outdoor
- Clock position: tells you the earth-pin location (4h, 6h, 9h) so plug only fits matching socket of same voltage
2. Industrial plug & socket price in Pakistan 2026
| Model | Type | Amperage | IP | Price PKR |
|---|---|---|---|---|
| CNC IS-16A-3P-IP44 | Single-phase 3-pin socket | 16A | IP44 | 1,800 |
| CNC IS-16A-3P-IP66 | Single-phase 3-pin socket | 16A | IP66 | 2,400 |
| CNC IS-32A-3P-IP44 | Single-phase 3-pin socket | 32A | IP44 | 2,800 |
| CNC IS-32A-3P-IP66 | Single-phase 3-pin socket | 32A | IP66 | 3,500 |
| CNC IS-16A-5P-IP44 | 3-phase 5-pin socket | 16A | IP44 | 2,400 |
| CNC IS-32A-5P-IP44 | 3-phase 5-pin socket | 32A | IP44 | 3,200 |
| CNC IS-32A-5P-IP66 | 3-phase 5-pin socket | 32A | IP66 | 4,800 |
| CNC IS-63A-5P-IP44 | 3-phase 5-pin socket | 63A | IP44 | 5,800 |
| CNC IS-63A-5P-IP66 | 3-phase 5-pin socket | 63A | IP66 | 7,500 |
| CNC IS-125A-5P-IP67 | 3-phase 5-pin socket | 125A | IP67 | 14,500 |
| CNC IP-32A-3P-IP44 | Single-phase 3-pin plug | 32A | IP44 | 1,600 |
| CNC IP-32A-5P-IP44 | 3-phase 5-pin plug | 32A | IP44 | 2,200 |
| CNC IP-63A-5P-IP66 | 3-phase 5-pin plug | 63A | IP66 | 4,500 |
| CNC ISG-32A-Lockable | Wall socket + circuit breaker (32A) | 32A | IP44 | 5,800 |
3. Sizing for Pakistani applications
| Application | Recommended socket |
|---|---|
| Workshop 16A single-phase tools | 16A 3-pin IP44 |
| Welding plant (single-phase) | 32A 3-pin IP44 |
| 3-phase factory power tools (5 HP motor) | 32A 5-pin IP44 |
| EV charger 7 kW dedicated outdoor | 32A 3-pin IP66 |
| Industrial pump 10 HP 3-phase outdoor | 32A 5-pin IP66 |
| Mobile generator output (large) | 63A 5-pin IP66 with isolator |
| Heavy industrial 50 HP motor | 125A 5-pin IP67 |
| Stage / event power feed | 63A 5-pin IP66 |
4. Wall-box installation
- Pick socket location: 1.2m above floor for protection from water on the ground.
- Cut wall-box hole sized per socket back-box (typically 50mm or 70mm diameter).
- Run cabling from upstream MCB or RCBO. Use 2.5mm² for 16A, 4mm² for 32A, 10mm² for 63A.
- Wire L1 (and L2, L3 for 3-phase), N, and Earth to socket terminals per IEC 60309 colour code.
- Tighten gland nut over cable for IP66 sealing if outdoor mount.
- Affix faceplate; verify earth continuity from socket pin to building earth bar.
5. FAQ
Cheapest industrial socket in Pakistan 2026?
CNC IS-16A-3P-IP44 at PKR 1,800 — 16A single-phase, indoor-rated IP44, IEC 60309 standard.
IP44 vs IP66 — which do I need?
IP44 for indoor workshops + protected outdoor. IP66 for fully exposed outdoor (factory yards, stage power, fuel stations).
3-pin vs 4-pin vs 5-pin?
3-pin = single-phase (L + N + E). 4-pin = 3-phase without neutral (3 phases + E). 5-pin = 3-phase + neutral (3 phases + N + E). Modern installations almost always use 5-pin for 3-phase.
Can I use a 16A industrial socket for a 32A load?
No — ampere rating is the maximum continuous current. Using a 16A socket for a 32A load will overheat contacts and may melt the housing.
Are CNC industrial sockets PSQCA-approved?
Yes — PSQCA mark + IEC 60309-1/2 certification + 5-year warranty in Pakistan.
6. Related guides
7. Need industrial sockets for your install?
WhatsApp +92 326 1111 376. Free Pakistan delivery on orders over PKR 5,000.