Push Button Switch Price in Pakistan 2026 — Industrial 22mm Buyer's Guide (LAY5 Series) | CNC Electric

What Is a Push Button Switch?

A push button switch is a momentary or maintained-contact electrical switch operated by manually pressing a head or actuator. In industrial Pakistan, push buttons are the primary human-to-machine interface on motor-starter panels, control stations, conveyors, lifts, generator-changeover panels, and the red mushroom-head emergency-stop devices that lock down entire production lines.

Last updated: 19 May 2026 · By CNC Electric Pakistan

Push buttons look simple, but selecting the right type matters: head shape, contact configuration (NO vs NC), illumination, IP rating, color code, and panel-cutout size all affect whether the device will survive a Pakistani factory environment for 5 years or fail in 5 months. This guide walks through every push button category sold in Pakistan in 2026, current CNC LAY5 series pricing, wiring with contactors, and the buyer's FAQ.

Push Button Switch Price in Pakistan 2026 (CNC LAY5 Series)

Live prices for CNC Electric industrial push buttons sold through authorised channels in Pakistan as of May 2026. All LAY5 series buttons fit the international 22mm panel-cutout standard:

Model	Type	Head Color	Action	Price (Rs.)
LAY5-EA45 Green	Flush Push Button	Green	Momentary NO	275
LAY5-EA45 Red	Flush Push Button	Red	Momentary NC	275
LAY5-ES545-R	Mushroom E-Stop	Red (40mm head)	Latching Twist-Release	350

Prices include 18% GST. Free shipping to Lahore, Karachi, Islamabad, Rawalpindi and 50+ cities on orders over Rs. 5,000. Cash-on-delivery available nationwide. Browse the full Push Button Switches range for live stock and color options.

Types of Push Button Switches Explained

1. Momentary Push Button (Spring-Return)

A momentary push button closes the contact only while the operator is pressing it; the moment pressure is released, the internal spring pops it back to its original state. This is the standard START / STOP behaviour: press green to start (closes the contactor coil circuit), the contactor's auxiliary contact "seals in" (latches), then the green button can be released. Press red to stop (breaks the seal-in), the contactor opens, motor stops.

The CNC LAY5-EA45 Red & Green at Rs. 275 each is the standard momentary push button — flush mount, 22mm cutout, 1NO + 1NC contact block, rated 10A at 230V AC.

2. Latching / Maintained Push Button

A latching push button stays in the pressed position until the operator presses it again (or twists / pulls to release). Used for selector functions: "Manual / Auto" mode, "Local / Remote" control, "Light On / Light Off." For lighting and continuous-mode applications, a maintained-contact button is the right choice.

3. Emergency Stop Button (Mushroom Head)

The emergency stop button (E-stop, mushroom-head, "emergency push button") is the safety-critical latching device required on every machine that can hurt people. Pressing it instantly opens the control circuit — motor stops, conveyor halts, press goes back to safe position — and the button stays latched until manually twisted or pulled to release. This prevents anyone from accidentally restarting the machine before the hazard is addressed.

The CNC LAY5-ES545-R Emergency Stop Push Button at Rs. 350 is the standard 40mm red mushroom-head E-stop required by IEC 60204-1 (safety of machinery). Twist-to-release action, 1NC + 1NO contact block, 22mm cutout.

4. Illuminated Push Button

Illuminated push buttons have an integrated LED that lights up when the function is active. Common configurations: red lamp inside a red "STOP" button (lights when motor is running and stop is available), green lamp inside a green "START" button (lights when machine is ready to start), or amber lamp inside a yellow "RESET" button (lights when a fault needs acknowledgement). Lamp voltage is selectable: 24V DC, 110V AC, 220V AC.

5. Selector Switch (Rotary Push Button)

A selector switch (rotary 2-position or 3-position knob) is functionally a multi-position push button. Used for mode selection: "OFF / MANUAL / AUTO" on a pump panel, "LOCAL / REMOTE" on a SCADA control station, or "FORWARD / OFF / REVERSE" on a motor drive. See our dedicated Selector Switch Guide for wiring and applications.

Push Button Color Codes (IEC 60073 / IEC 60204)

Push button colors are standardised internationally to prevent operator confusion in a critical moment. Follow these conventions in every panel you build:

• Red — STOP, OFF, Emergency-Stop, Reset-after-fault. Single most important color. Never use red for anything other than stopping or emergency.
• Green — START, RUN, ON, Normal Action. The "go" color.
• Yellow / Amber — RESET, Intervention Required, Caution, Override. For dispatching a fault or overriding an automatic function.
• Blue — Mandatory Action (e.g., manual lubricate, manual lock). Less common in Pakistani panels.
• White / Grey / Black — Neutral / unspecified action. Used for jog functions, lights, miscellaneous controls.

For an emergency stop, the head MUST be red with a yellow background plate (per IEC 60204-1) and the actuator must be a mushroom shape so it can be slapped without precise aim.

NO vs NC — Understanding Contact Configuration

Every push button has one or more contact blocks behind the head, each containing either a Normally Open (NO) or Normally Closed (NC) contact pair:

• Normally Open (NO) — contacts are OPEN when the button is released. Pressing the button CLOSES the contact. This is the standard "start" behaviour — green START buttons are typically NO.
• Normally Closed (NC) — contacts are CLOSED when the button is released. Pressing the button OPENS the contact. This is the standard "stop" behaviour — red STOP buttons are typically NC (so the motor runs as long as the stop button is NOT pressed; this is fail-safe).

Most CNC LAY5 push buttons ship with a 1NO + 1NC contact block, allowing the same button to be wired as either a start or a stop in any motor circuit. For complex panels (e.g. dual-function jog buttons), you can add additional contact blocks underneath the head — up to 3 blocks per push button.

Push Button Wiring with a Contactor

The classic DOL (Direct On Line) motor starter circuit uses two push buttons and one contactor:

1. Control supply (e.g. 220V AC from one phase + neutral)
2. Stop push button (Red, NC) — wired in series
3. Start push button (Green, NO) — wired in series, with a parallel hold-in path through the contactor's auxiliary NO contact
4. Contactor coil (A1 terminal)
5. Back to control-supply neutral

Pressing GREEN momentarily energises the coil; the contactor pulls in and its NO auxiliary contact closes, providing a parallel path around the green button — this is the "hold-in" or "seal-in" circuit. Pressing RED breaks the series path, de-energising the coil and dropping out the contactor. For full wiring diagrams with terminal numbers, see our Magnetic Contactor Wiring Guide.

Panel-Mount Cutout — The 22mm Standard

All CNC LAY5 push buttons use the international 22mm panel-cutout standard. To install a push button on your control panel:

1. Mark the centre of the desired button location on the panel door / faceplate
2. Drill a 22mm hole (use a step drill or hole punch for clean cuts)
3. Insert the push button head from the front
4. Slide the contact block + retaining nut from behind
5. Tighten with 2-3 Nm of torque (do not over-tighten — the plastic body will crack)
6. Wire the contact terminals (typically screw terminals, max 1.5 sq mm wire)

Centre-to-centre spacing on a typical control panel: 30mm between adjacent buttons. For an aesthetic and ergonomic layout, group START buttons (green) on the right and STOP buttons (red) on the left, with the EMERGENCY STOP isolated and easily reachable from any operator position.

IP Rating — Will It Survive Your Environment?

The IP (Ingress Protection) rating tells you whether the push button will keep dust and water out:

• IP40 — dust-protected, no water protection. Indoor / climate-controlled panels only.
• IP65 — dust-tight, protected against water jets. Suitable for outdoor enclosures, factory floors, food-processing rooms. CNC LAY5 series.
• IP67 — dust-tight, can survive temporary immersion. Used for wash-down areas (dairies, abattoirs, beverage plants).

For typical Pakistani factory / commercial installations, the IP65-rated CNC LAY5 series is the right balance of cost and protection. Always pair an IP65 push button with an IP65-rated enclosure — putting a sealed button in a leaky cabinet defeats the purpose.

Top 5 Push Button Picks for 2026

1. Best Overall — CNC LAY5-EA45 Green / Red — Rs. 275 each

The LAY5-EA45 Push Button Switch Red & Green is the standard 22mm flush-mount industrial button for every Pakistani motor-starter and ATS panel. 1NO + 1NC contact block, 10A AC15 rating, IP65 from the front. Buy one of each color for a basic start/stop circuit.

2. Best Safety — CNC LAY5-ES545-R Emergency Stop — Rs. 350

The LAY5-ES545-R Emergency Stop 40mm red mushroom-head is mandatory for every machine that can injure people. Twist-to-release latching action, 1NC + 1NO contact, IEC 60947-5-5 safety compliance. Install at every operator position and on every external panel face.

3. Best for Lift / Elevator Panels — LAY5 Illuminated 220V AC

For lift / elevator control stations, illuminated LAY5 buttons (with 220V AC LED indicator) show floor selection and door-control status in low-light cabin environments. Specify "with LED" when ordering — base button + LED block + retaining ring.

4. Best for Industrial Production Lines — LAY5 with 2NO + 2NC Block

For motor starters that need separate "running" and "fault" indicator circuits, the LAY5 base button accepts up to 2NO + 2NC stacked contact blocks. Add additional blocks underneath the head — same Rs. 275 base price + Rs. 150 per extra block.

5. Best Mode Selector — CNC LAY5 Selector Switch

For "Manual / Auto" or "Local / Remote" selection on a PLC-controlled panel, use the LAY5 2-position or 3-position selector switch. See our Selector Switch Guide for sizing and wiring.

Common Push Button Problems and Solutions

"Button is stuck and won't return"

Dust or debris has fouled the spring. Disconnect power, unscrew the contact block, and remove the head. Clean with compressed air or contact cleaner. If the plastic actuator is cracked, replace the entire push button — repair is not cost-effective at Rs. 275 per unit.

"Pressing the button does nothing"

Check three things in this order: (1) Is the control supply present at the contact-block terminals? (2) Is the wire connection at the contact block tight? (3) Does the contact actually close on press — measure continuity between the COM and NO terminals with a multimeter. If the contact block is faulty, replace just the contact block (Rs. 150) — no need to replace the head.

"Emergency stop button won't release"

This is normal behaviour — E-stops are designed to LATCH until manually reset. Twist the head clockwise (per the arrow on the button face) to release. If it still won't release, the internal latching mechanism is damaged — replace the entire E-stop button.

"Button heats up when motor runs"

The push button is wired into the motor power circuit instead of the control circuit. This is dangerous — most LAY5 push buttons are rated 10A at 230V AC for control duty only. Re-wire the panel so the push button drives only the contactor coil, and the contactor switches the motor power. Never use a push button to switch motor-load current directly.

Bulk and Dealer Pricing for Push Buttons

CNC Electric offers project pricing for panel builders, electrical contractors, machine OEMs, and B2B orders:

• 25-100 push buttons: 8% off list price
• 101-500 push buttons: 13% off list price
• 500+ push buttons / panel-builder OEM quotes: ask for project pricing

For panel-builder pricing, contact-block-only quotations, custom-laser engraving (operator labels in Urdu or English), or PSQCA-certified shipments, message us on WhatsApp via the floating button on this page, or browse the complete Push Button range.

Frequently Asked Questions

What is the difference between a push button and a switch?

A push button is a momentary-contact switch — the contact changes state only while you are pressing the button, then springs back. A regular switch (toggle switch, rocker switch) is maintained-contact — the contact stays in whichever position you set it. Push buttons are used in industrial control circuits because they let operators give a momentary "start" or "stop" command, with the actual hold-in being handled by a contactor's seal-in circuit.

How much does a push button switch cost in Pakistan in 2026?

CNC Electric LAY5 series industrial push buttons in Pakistan in 2026 cost Rs. 275 for a standard red or green flush-mount button (1NO + 1NC contact block, 22mm cutout) and Rs. 350 for a 40mm red mushroom-head emergency-stop button (1NC + 1NO, twist-to-release). Illuminated and multi-block variants are slightly more.

What is the standard panel cutout for a push button?

The international standard is 22mm diameter for industrial push buttons — this matches Schneider XB7/XB4, ABB CP1/CP2, Siemens 3SU, CNC LAY5, and most other major brands. A 22mm push button from one brand is mechanically interchangeable with any other brand's 22mm button. Older imperial-system panels use 30.5mm — these are rare in modern Pakistani factories and obsolete for new builds.

What color should I use for a start button?

Use GREEN for START / RUN / ON. This is mandated by IEC 60204-1 and is the international convention. Never use red for start — that's reserved for STOP. Yellow / amber is reserved for RESET or intervention. Blue for mandatory action (rare). White / grey for jog or miscellaneous.

Are emergency stop buttons legally required in Pakistan?

For factory machinery, yes — under the Factories Act 1934 and PSQCA machinery-safety regulations. Every machine that can injure an operator must have at least one accessible emergency-stop button per operator position. For industrial / commercial buildings, emergency stops on lifts, escalators, and HVAC systems are similarly mandated. Insurance audits regularly cite missing E-stops as a non-compliance.

Can I use a push button with a 220V AC motor directly?

No — never. CNC LAY5 push buttons are rated for control circuits only (max 10A at 230V AC). Wiring a push button directly into a motor's power line will weld the contacts shut, melt the plastic housing, and create a serious fire risk. Always wire the push button to drive only the contactor coil; the contactor then switches the motor power.

Are CNC push buttons PSQCA-approved?

Yes. All CNC Electric LAY5-series push buttons sold in Pakistan are PSQCA-registered and built to IEC 60947-5-1 (low-voltage switchgear and controlgear — electromechanical control circuit devices) and IEC 60947-5-5 (electrical emergency-stop devices with mechanical latching function) compliance. Each unit ships with a CE conformity declaration and a 12-month CNC warranty.

How long does a push button last?

Mechanical life of a CNC LAY5 push button is 1 million operations at rated AC15 load. In a typical Pakistani factory (100 button presses per shift), this works out to a 10-15 year service life before the contact block needs replacement. Emergency-stop buttons last longer because they are pressed only in actual emergencies — typically once every few years.

Do you ship push buttons nationwide in Pakistan?

Yes. CNC Electric ships push buttons to all major cities — Lahore, Karachi, Islamabad, Rawalpindi, Faisalabad, Multan, Peshawar, Quetta, Hyderabad, Sialkot, Gujranwala, Sargodha — usually within 2-3 working days. Cash-on-delivery available; bulk orders and OEM-volume orders can be picked up from the Lahore warehouse.

---

Related guides: Contactor Price Guide 2026 · Magnetic Contactor Wiring Guide · Selector Switch Guide · Timer Switch Guide · MCB Full Form Guide · DB Box Wiring Guide